Especificaciones técnicas

SPL
121 dB

Potencia del amplificador
500 W Bass (Class D) + 250 W Midrange (Class D) + 200 W Treble (Class AB)

Respuesta en frecuencia
30 Hz - 22 kHz ("-6 dB")

Precisión de la respuesta en frecuencia
± 2.5 dB (35 Hz - 20 kHz)

Dimensiones del altavoz
⌀ 385 mm Bass + ⌀ 125 mm Midrange + ⌀ 25 mm Treble (ver en pulgadas)

Dimensiones
H 810 x W 480 x D 420 mm, (ver en pulgadas)

Peso
57 kg / 125.7 lb

Conexiones
1 x XLR Analog Input
1 x XLR AES/EBU Input
1 x XLR AES/EBU Output
2 x RJ45 Control
1238A SAM™ Studio Monitor
SAM™ Studio Monitor
Especificaciones técnicas
Our largest three-way midfield design, the 1238A adapts to your acoustic space to deliver high-SPL reference precision.

Especificaciones del sistema
Respuesta en frecuencia
35 Hz - 20 kHz (± 2.5 dB)
Corte de graves -6 dB
30 Hz
Corte de agudos -6 dB
22 kHz

SPL
SPL pico Maximum peak acoustic output per pair in a listening room with music material at 2 m.
≥124 dB
SPL máximo a corto plazo Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz at 1 m.
≥121 dB
Máximo SPL a largo plazo Maximum long term RMS acoustic output in the same conditions with IEC weighted noise (limited by driver unit protection circuit) at 1 m.
≥116 dB
Ruido propio
Ruido propio Self generated noise level in free field at 1 m on axis (A-weighted).
≤10 dB SPL
Peso
Peso57 kg (125.7 lb)
Dimensiones
Altura
810 mm
Anchura
480 mm
Profundidad
420 mm

Recinto
Material del recinto
MDF
Tipo de recinto
Reflex port
Altavoces
Tipo de altavoz
Cone
385mm (15 in) cone
Diámetro
385 mm
Tipo de altavoz
Cone
125 mm (5 in) cone
Diámetro
125 mm
Tipo de altavoz
Metal dome
25mm (1 in) metal dome
Diámetro
25 mm
Directividad

Distorsión armónica
> 200 Hz ≤0.5 %
Retardo de grupo
The latency at high frequencies from the input to the acoustic output, measured in the analog input:
Extended Phase Linearity in GLM set to OFF
5.1 ms
In Genelec performance graphics, the time of converting the from an electronic input signal to the acoustic output in a Genelec monitor is described by two factors – latency and group delay. The group delay factor can be read in the graphics for a specific frequency. The total frequency-specific input-to-output delay is a sum of the latency and group delay factors. To understand the significance of this total delay, consider that moving a loudspeaker away by 1 meter creates an additional delay of about 3 ms.

Sección de amplificación
Amplificadores
500 W Class D
Altura
132 mm
Anchura
483 mm
Profundidad
252 mm
Peso
6 kg
(13.2 lb)
250 W Class D
200 W Class AB
Voltaje de la toma eléctrica
100-240 VAC 50/60Hz
Consumo de potencia
Con ISS activo
≤0.5 W
En reposo
≤25 W
A pleno rendimiento
750 W
Sección de procesado de señal
Conectores
Input Analog signal input connector XLR female, balanced 10 kOhm.
Input Digital signal input connector XLR female 110 Ohm.
Output Digital signal output / Thru connector XLR male 110 Ohm.
2 x Control Two CAT5 (RJ45) GLM Network connectors for computer control using the Genelec Loudspeaker Manager (GLM) software.