Especificaciones técnicas
SPL
130 dB
Potencia del amplificador
2 X 1000 W Bass (Class D) + 2 X 400 W Midrange (Class D) + 250 W Treble (Class D)
Respuesta en frecuencia
17.5 Hz - 26 kHz ("-6 dB")
Precisión de la respuesta en frecuencia
± 2 dB (21 Hz - 20 kHz)
Dimensiones del altavoz
2 x ⌀ 458 mm Bass + 2 x ⌀ 125 mm Midrange + ⌀ 25 mm (ver en pulgadas)
Dimensiones
H 1180 x W 960 x D 650 mm, (ver en pulgadas)
Peso
182 kg / 401.2 lb
Conexiones
1 x XLR Analog Input
1 x XLR AES/EBU Input
1 x XLR AES/EBU Output
2 x RJ45 Control
1236A SAM™ Studio Monitor
SAM™ Studio Monitor
Especificaciones técnicas
The flagship of our range. The intelligence of the 1236A is seamlessly integrated into the finest example of acoustic engineering yet produced in more than 40 years of Genelec history.
Especificaciones del sistema
Respuesta en frecuencia
21 Hz - 20 kHz (± 2 dB)
Corte de graves -6 dB
17.5 Hz
Corte de agudos -6 dB
26 kHz
SPL
SPL pico Maximum peak acoustic output per pair in a listening room with music material at 2 m.
≥136 dB
SPL máximo a corto plazo Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz at 1 m.
≥130 dB
Máximo SPL a largo plazo Maximum long term RMS acoustic output in the same conditions with IEC weighted noise (limited by driver protection circuit) at 1 m.
≥125 dB
Ruido propio
Ruido propio Self generated noise level in free space at 2 m on axis (A-weighted).
≤5 dB SPL
Peso
Peso182 kg (401.2 lb)
Dimensiones
Altura
1180 mm
Anchura
960 mm
Profundidad
650 mm
Recinto
Material del recinto
MDF
Tipo de recinto
Reflex port
Altavoces
Tipo de altavoz
Cone
Cantidad
2
Diámetro
458 mm
Tipo de altavoz
Cone
Cantidad
2
Diámetro
125 mm
Tipo de altavoz
Compression
Compression tweeter 50 mm (2 in) into 25 mm (1 in) throat
Diámetro
25 mm
Directividad
Distorsión armónica
100 Hz...3 kHz ≤0.5 %
> 3 kHz ≤3 %
Retardo de grupo
The latency at high frequencies from the input to the acoustic output, measured in the analog input:
Extended Phase Linearity in GLM set to OFF
5.2 ms
In Genelec performance graphics, the time of converting the from an electronic input signal to the acoustic output in a Genelec monitor is described by two factors – latency and group delay. The group delay factor can be read in the graphics for a specific frequency. The total frequency-specific input-to-output delay is a sum of the latency and group delay factors. To understand the significance of this total delay, consider that moving a loudspeaker away by 1 meter creates an additional delay of about 3 ms.
Sección de amplificación
Amplificadores
2 x 1000 W Class D
3U Rack mounted amplifier
Altura
132 mm
Anchura
483 mm
Profundidad
286 mm
Peso
11.2 kg
(24.7 lb)
2 x 400 W Class D
3U Rack mounted amplifier.
Altura
132 mm
Anchura
483 mm
Profundidad
286 mm
Peso
11.2 kg
(24.7 lb)
250 W Class D
3U Rack mounted amplifier.
Altura
132 mm
Anchura
483 mm
Profundidad
286 mm
Peso
11.2 kg
(24.7 lb)
Voltaje de la toma eléctrica
100-120VAC / 220-230VAC 50/60Hz
Consumo de potencia
Con ISS activo
≤6 W
En reposo
≤40 W
A pleno rendimiento
2400 W
Sección de procesado de señal
Conectores
Input Analog signal input connector XLR female, balanced 10 kOhm.
Input Digital signal input connector XLR female 110 Ohm.
Output Digital signal output / Thru connector XLR male 110 Ohm.
2 x Control Two CAT5 (RJ45) GLM Network connectors for computer control using the Genelec Loudspeaker Manager (GLM) software.