Especificaciones técnicas
SPL
130 dB
Potencia del amplificador
2 X 1000 W Bass (Class D) + 2 X 400 W Midrange (Class D) + 250 W Treble (Class D)
Respuesta en frecuencia
29 Hz - 26 kHz ("-6 dB")
Precisión de la respuesta en frecuencia
± 2 dB (31 Hz - 20 kHz)
Dimensiones del altavoz
2 x ⌀ 381 mm Bass + 2 x ⌀ 125 mm Midrange + ⌀ 25 mm Treble (ver en pulgadas)
Dimensiones
H 820 x W 1105 x D 650 mm, (ver en pulgadas)
Peso
164 kg / 361.6 lb
Conexiones
1 x XLR Analog Input
1 x XLR AES/EBU Input
1 x XLR AES/EBU Output
2 x RJ45 Control
1235A SAM™ Studio Monitor
SAM™ Studio Monitor
Especificaciones técnicas
The 1235A brings the sound and heritage of the iconic 1035 into the modern recording age. High SPL capability and precise imaging come together in a main monitor that adapts to your room.
Especificaciones del sistema
Respuesta en frecuencia
31 Hz - 20 kHz (± 2 dB)
Corte de graves -6 dB
29 Hz
Corte de agudos -6 dB
26 kHz
SPL
SPL pico Maximum peak acoustic output per pair in a listening room with music material at 2 m.
≥135 dB
SPL máximo a corto plazo Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz at 1 m.
≥130 dB
Máximo SPL a largo plazo Maximum long term RMS acoustic output in the same conditions with IEC weighted noise (limited by driver protection circuit) at 1 m.
≥124 dB
Ruido propio
Ruido propio Self-generated noise level in free space at 2 m on axis (A-weighted).
≤5 dB SPL
Peso
Peso164 kg (361.6 lb)
Dimensiones
Altura
820 mm
Anchura
1105 mm
Profundidad
650 mm
Altavoces
Tipo de altavoz
Cone
Cantidad
2
Diámetro
381 mm
Tipo de altavoz
Cone
Cantidad
2
Diámetro
125 mm
Tipo de altavoz
Compression
Compression tweeter 50 mm (2 in) into 25 mm (1 in) throat
Diámetro
25 mm
Directividad
Distorsión armónica
100 Hz - 3 kHz ≤0.5 %
> 3 kHz ≤3 %
Retardo de grupo
The latency at high frequencies from the input to the acoustic output, measured in the analog input:
Extended Phase Linearity in GLM set to OFF
5.2 ms
In Genelec performance graphics, the time of converting the from an electronic input signal to the acoustic output in a Genelec monitor is described by two factors – latency and group delay. The group delay factor can be read in the graphics for a specific frequency. The total frequency-specific input-to-output delay is a sum of the latency and group delay factors. To understand the significance of this total delay, consider that moving a loudspeaker away by 1 meter creates an additional delay of about 3 ms.
Sección de amplificación
Amplificadores
2 x 1000 W Class D
3U Rack mounted amplifier
Altura
132 mm
Anchura
483 mm
Profundidad
286 mm
Peso
11.2 kg
(24.7 lb)
2 x 400 W Class D
3U Rack mounted amplifier
Altura
132 mm
Anchura
483 mm
Profundidad
286 mm
Peso
11.2 kg
(24.7 lb)
250 W Class D
3U Rack mounted amplifier
Altura
136 mm
Anchura
483 mm
Profundidad
286 mm
Peso
11.2 kg
(24.7 lb)
Voltaje de la toma eléctrica
100-120VAC / 220-230VAC 50/60Hz
Consumo de potencia
Con ISS activo
≤6 W
En reposo
≤40 W
A pleno rendimiento
2400 W
Sección de procesado de señal
Conectores
Input Analog signal input connector XLR female, balanced 10 kOhm.
Input Digital signal input connector XLR female 110 Ohm.
Output Digital signal output / Thru connector XLR male 110 Ohm.
2 x Control Two CAT5 (RJ45) GLM Network connectors for computer control using the Genelec Loudspeaker Manager (GLM) software.