Especificaciones técnicas

SPL
114 dB

Potencia del amplificador
250 W Bass (Class D) + 150 W Treble (Class D)

Respuesta en frecuencia
33 Hz - 23 kHz ("-6 dB")

Precisión de la respuesta en frecuencia
± 2.5 dB (40 Hz - 20 kHz)

Dimensiones del altavoz
⌀ 250 mm Bass + ⌀ 25 mm Treble (ver en pulgadas)

Dimensiones
H 495 x W 320 x D 290 mm, (ver en pulgadas)

Peso
17 kg / 37.5 lb

Conexiones
1 x XLR Analog Input
1 x XLR AES/EBU Input
1 x XLR AES/EBU Output
2 x RJ45 Control
1032C
SAM™ Monitor de Estudio
Especificaciones técnicas
El 1032C es un monitor de campo cercano con alto SPL que fusiona el muy querido estilo montable en plafón de la icónica serie 1000 con nuestra última tecnología de monitoreo activo inteligente.

Especificaciones del sistema
Respuesta en frecuencia
40 Hz - 20 kHz (± 2.5 dB)
Corte de graves -6 dB
33 Hz
Corte de agudos -6 dB
23 kHz

SPL
SPL pico Maximum peak acoustic output per pair in a listening room with music material at 1 m.
≥124 dB
SPL máximo a corto plazo Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz at 1 m.
≥114 dB
Máximo SPL a largo plazo Maximum long term RMS acoustic output in the same conditions with IEC weighted noise (limited by driver protection circuit) at 1 m.
≥104 dB
Ruido propio
Ruido propio Self generated noise level in free space at 1 m on axis (A-weighted).
≤5 dB SPL
Peso
Peso17 kg (37.5 lb)
Dimensiones
Altura
495 mm
Anchura
320 mm
Profundidad
290 mm

Recinto
Material del recinto
MDF
Altavoces
Tipo de altavoz
Cone
Magnetically shielded bass driver.
Diámetro
250 mm
Tipo de altavoz
Metal dome
Magnetically shielded treble driver.
Diámetro
25 mm
Directividad


Distorsión armónica
> 100 Hz ≤0.5 %
Retardo de grupo
The latency at high frequencies from the input to the acoustic output, measured in the analog input:
Extended Phase Linearity in GLM set to OFF
3.2 ms
In Genelec performance graphics, the time of converting the from an electronic input signal to the acoustic output in a Genelec monitor is described by two factors – latency and group delay. The group delay factor can be read in the graphics for a specific frequency. The total frequency-specific input-to-output delay is a sum of the latency and group delay factors. To understand the significance of this total delay, consider that moving a loudspeaker away by 1 meter creates an additional delay of about 3 ms.

Sección de amplificación
Amplificadores
250 W Class D
150 W Class D
Voltaje de la toma eléctrica
100-240 VAC 50/60Hz
Consumo de potencia
Con ISS activo
≤1 W
En reposo
≤11 W
A pleno rendimiento
200 W
Sección de procesado de señal
Conectores
Input Analog signal input connector XLR female, balanced 10 kOhm.
Input Digital signal input connector XLR female 110 Ohm.
Output Digital signal output / Thru connector XLR male 110 Ohm.
2 x Control Two CAT5 (RJ45) GLM Network connectors for computer control using the Genelec Loudspeaker Manager (GLM) software.